Description
x2 Flute - Solid Carbide
The industry’s solution for trimming aluminum laminates!
- Recommended by Formica® & ATI®
- Engineered from an Amana-exclusive carbide grade designed specifically for cutting both aluminum laminates and wood-based substrate materials.
- InVectra™ Aluminum laminate trim router bits - good for aluminum & copper
Designed & tested for trimming all decorative aluminum laminates. For use in all DecoMetal® material (exluding #2178) & Advanced Technology Inc. (ATI®). Each bit is fitted with a steel bearing guide that enables users to trim laminate materials flush to the substrate. Invectra™ router bits are available in two diameters, 1/4” (item 51430) and 1/2” (item 51432), with and without ZrN coating.
With Invectra™ router bits, kitchen fabricators, remodelers, cabinet makers and construction workers can perform any kind of cut and trim job in aluminum laminates using a table or hand-held router.
Note: Replacement washer for item 51432 and 51432-Z use 67053. L1 dimension for 51432 and 51432-Z is 5/32"
ZrN™ Coated Router Bits – Made in the USA 
Amana Tool® solid carbide router bits provide consistent, repeatable quality. Every tool is guaranteed to match the geometry on the prints, every time on every order. Best control of carbide grades for woodworking, and absolute control of quality standards on all carbide blanks.
ZrN Coating benefits:
Items #51430-Z and #51432-Z have ZrN coating
- Zirconium Nitride (ZrN) coating creates a harder and tougher cutting ceramic over carbide edge, allowing for a prolonged cutting edge life and helps to prevent the build-up/galling of material in the flutes while cutting
- ZrN coated bits have the ability to run and/or be spun much faster than an uncoated tools
- High flute volume supports high feed rates and chip loads
- High aspect ratio for single pass deep-reach cutting
- Creates incredibly precise detail work
- Mirror finish polished flute, up-spiral cutting edge for superior chip ejection
- Flute geometry optimized for cutting sign foam, sign board, hardwoods, thermoplastics and phenolic composites
- Optimized flute geometry and low Total Indicated Runout (TIR) guarantees clean cuts, essentially eliminates sanding and reduces chatter (where the machine or work piece vibrates) under high chip loads when used with low TIR spindles
Additional Information
xShipping & Returns
xShipping Policy
When you place an order, we will estimate shipping and delivery dates for you based on the size and weight of your items and the shipping options chosen. Depending on the shipping provider, shipping dates, and other factors, estimates may or may not appear on the shipping quotes page, or be entirely accurate for all destinations and scenarios.
Please also note that the shipping rates for many items we sell are weight-based. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.
Tool Factory Outlet sells a wide variety of products and equipment that ship via Freight. Products that ship Freight typically weigh more than 150lbs or exceed a certain length, or both. If your product is shipping Freight, it will be indicated during check-out as "Freight Shipping." If your product is shipping Freight and Free Shipping is not offered for that specific product, you will receive a separate shipping invoice for you to accept or decline. You will have to coordinate last-mile delivery of the product with the carrier. Typical options include customer pick-up from the terminal, lift gate service to a residential address, or trailer delivery to a loading dock equipped business or building. The carrier will contact you to arrange this. If you have any questions, please call or email us directly.
Returns Policy
You may return most new, unopened items within 30 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).
You should expect to receive your refund within 4-10 days of our warehouse receiving back your product, however, in many cases you will receive your refund even faster.
If you need to return an item, simply login to your account, view the order using the "Complete Orders" link under the My Account menu and click the Return Item(s) button. Once we review and approve your request, an RMA will be issued via email. We'll also notify you via e-mail of your refund once we've received, inspected, and processed the returned item.
- Choosing a selection results in a full page refresh.
